Stepper Motor Driver
Showing all 16 results
-
Stepper Motor Driver
3D Printer Controller Board RAMPS 1.4 Arduino Mega Shield RepRap Prusa Model
- Supply Voltage: 12V
- Standard interfaces (as that of the extruder)
- Reserved GCI like I2C and RS232
- 3 MOSFET’s are applied to the heater/ fan and thermistor circuit.
- Another 5A added to protect the component parts.
- An 11A fuse is added to the hotbed.
- Support 5 stepper drive board
SKU: 800605 -
-
-
Stepper Motor Driver
A4988 Stepper Motor Driver Controller Board- RED
- Compact size, easy to install and use.
- All jumpers hit the ON position to indicate 16 subdivisions (4988) or 32 subdivisions (8825).
- Jm connection motor: Jv Connects 5V and 12V-24V Power Supply.
- E /S /D /G of Jc corresponds to Enable /Step /Dir /Gnd driving signal output on the connection respectively.
SKU: 800602 -
-
Stepper Motor Driver
Cytron 20Amp 6V-30V DC Motor Driver MD20A
- Bidirectional control for one brushed DC motor.
- Operating Voltage: DC 6V to 30V
- Maximum Motor Current: 20A continuous, 60A peak
- Buttons for quick testing.
- LEDs for motor output state.
- Overcurrent protection with active current limiting.
- Temperature protection.
- Undervoltage shutdown.
SKU: 800611 -
Stepper Motor Driver
DRV8825 Stepper Motor Driver with Aluminum Heat Sink- Good Quality
- Supply Voltage: 8.2 – 42 VDC.
- Current Capacity : 2.2A max(24V).
- Continuous current per phase: 1.5 A.
- Minimum Logic voltage: 2.5V.
- Maximum Logic Voltage: 5V.
- Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Dimensions : 15 x 20 mm.
- Weight: 4 gm.
SKU: 800610 -
Stepper Motor Driver
L298N Dual H Bridge DC/Stepper Motor Driver Controller Module
- Driver chip: L298N Dual H Bridge
- Supply voltage: VMS 5V – 35V
- Peak current IO: 2A per bridge
- Max power consumption: 20W
- Provides 4 LEDs that reflect the state of the control logic
- Independent direction, speed, and braking for each motor
SKU: 800615 -
Stepper Motor Driver
L9110 L9110S DC Stepper Motor Driver Board HBridge
- Power supply voltage: DC2.5-12V
- Each channel has 800mA continuous current output
- Low saturation pressure drop
- TTL/CMOS output level compatible can be connected directly to the CPU
- Control and drive integrated into IC
- Have pin high-pressure protection function
SKU: 800608 -
-
Stepper Motor Driver
MACH3 Interface Board CNC 5 Axis with Optocoupler for Stepper Motor Driver and USB cable
Stepper Motor DriverMACH3 Interface Board CNC 5 Axis with Optocoupler for Stepper Motor Driver and USB cable
- Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
- USB power supply and peripherals power phase are separate to protect computer security.
- All the signals are to-isolate which can protect your computer security.
- 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
- Wide input voltage range: 12-24V, and with anti-reverse function.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
SKU: 800603 -
Stepper Motor Driver
TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor
- Driver Chip: TB6560AHQ
- Operating Voltage: 10-35V
- Nominal Voltage: 24V
- With the large heat sink to ensure good heat dissipation
- 6N137 high-speed OptoCoupler, to ensure a high speed without step out.
SKU: 800607 -
-
Stepper Motor Driver
TB6600 Stepper Motor Driver Controller 8~50V 4.5A
- Supply Voltage: 8V – 50V DC (36V recommended).
- Output current: 0.3A – 4.5A (peak value of 5A).
- Micro Step: 1, 2, 8, 16.
- Maximum PWM frequency: 200kHz.
- Adjustments for the maximum current of the LED: 1A, 2.2A, 3.3A, 4.5A.
- Operating temperature: -10 to + 45 °C.
SKU: 800612 -
Stepper Motor Driver
ULN2003 Driver Module Stepper Motor Driver
- 5-12V power supply
- 4-way signal indicator
- Chip all the pins have Input leads Mounted for easy connection to use
- XH-5P socket can be connected directly 28BYJ-48 Model stepper motor
- Dimensions: 32 x 18 x 11mm (LxWxH)
- Weight: 3 gm
SKU: 800601 -