3.3V Adapter Board for 24L01 Wireless Module
- It can be used with NRF24L01 wireless module
- Add core nRF24L01+ Breakout Adapter with onboard 3.3V Regulator
- Onboard 3.3V voltage regulator accepts your Arduino +5V supply and provides 3.3V for the attached nRF24L01+ module
- Allows for easy connection to nRF24L01+ modules
- Small power on SMD LED indicator
CH340G USB to RS232 TTL Auto Converter Adapter Module for Arduino
- Resettable fuse with 500mA
- 3.3V / 5V real switchable
- 3.3V comes with the transformer
- Green Data reception mentioning an indicator
- Multifunction CTS access products
- Dual protection circuit
- Full-function pins 5P
- Blue power indicator
CH340G USB To TTL(Serial) Converter For Arduino Nano Raspberry Pi
- Built-in USB to TTL Transfer chip.
- Designed to be used for USB to TTL electronic projects.
- TTL interface output, easy to connect to your MCU.
- Dual 3.3V and 5V Power output, work with 3.3v and 5 V target device.
- The mini-module is designed specifically for STC download and ARDUINO PRO supports all series of STC
- Supports WIN7/VISTA/MAC/LINUX(32 bit /64-bit system)
CH341A 24 25 Series EEPROM Flash BIOS USB Programmer with Software & Driver
- USB interface
- With CH341A chip
- Support 24 EEPROM and 25 SPI flash 8pin or 16pin chip
- With 24/25 status indicator lamp
- Support USB to TTL conversionSupport 24EEPROM and 25 SPI flash 8pin/ 16pin chip
- Recognize 25 series chip automatically
- Supports download STC series procedure of single chip
- SPI pin to support expanding the utility
- STC microcontroller supports a full range of program download
- Support expanding the utility by SPI pin
- With SOP8 SOP16 to DIP8 converter board
CP2102(6-pin) USB 2.0 to TTL UART serial converter
- Brand new and high quality
- Included USB transceiver, without external circuit device
- With 3.3V and 5V dual power output
- With three LEDs: power indicator, data reception indicator, the data transmission indicator, working status
- Meets the USB2.0 specification requirements
- With self-recovery fuse. In the event of the accidental short circuit, it can effectively protect your computer USB port and Downloader
- Asynchronous serial data bus compatible with all handshake and modulation controller interface signals
- The supported data format is 8 data bits, 1 stop bit and parity bits
DB9 Female Screw Terminal to RS232 RS485 Conversion Board
- Brings all 9 pins of a DB9 connector to screw terminal blocks
- Adapter used for communication debug
- 9 pcs signal line was all lead out, name and number clearly labeled;
- All-copper DR9 seat, anti-oxidation, better contact;
- Military board, three anti-paint sprays an entire board, corrosion-resistant;
- Terminal spacing 3.96MM, screw hole diameter 2MM, need to use a width of 2MM screwdriver for assembly;
- Use of environmentally friendly copper terminals, through IS0-9001.
IIC/I2C Serial Interface Adapter Module
- 5V power supply.
- Serial I2C control of LCD display using PCF8574.
- Backlight can be enabled or disabled via a jumper on the board.
- Contrast control via a potentiometer.
- Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
MAX485 TTL To RS485
- On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver.
- A low power consumption for the RS-485 communication
- Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring.
- Slew-rate limited transceiver
- All pins of the chip have been lead to can be controlled through the microcontroller.
- Convenient RS-485 communication wiring
- Multiple Units can be connected to the same RS-485 bus wiring.
- All Chip pins are brought out for proper controls
PL2303 PL2303HX USB To TTL(Serial) Converter Module – 5 Pin
- Adopt imported controller PL2303HX, which can stabilize the flash with high speed
- 500mA self-recovery fuse for protection
- Two data transmission indicator can monitor data transfer status in real time
- Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power
- The entire board is coated by the high quality transparent heat-shrinkable sleeve, making the PCB in insulation state from outside,
- so that the board won’t be burnt down by material shortcut.
- Electrostatic package ensures the board will not be damaged before use
PL2303 TA Download Cable USB to TTL RS232 Module USB to Serial
- Built-in TTL COM PC-PL2303HX Chip.
- Standard USB type and TTL 4 pin connector
- Simple and Easy way to give USB support to your designs
- Available for Linux, Mac, WinCE, and Windows (XP, 7), Win 8
- Cable Length: 1M
- Net Weight: 30gm
SD Card Reading Writing Module for Arduino
- All SD SPI pins output, MOSI, SCK, MISO, and CS.
- Support 5V/3.3V input.
- This module can handle 2GB SD cards.
- Size:4.7 x 3.1 cm.
- LED indicator.
- SD Card Holder.
- Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
TTL FTDI Transmitter USB For 3.3V/5V Dual power FT232RL MWC Programmer
- USB Connector type: USB-Mini
- Chip Used: FT232RL
- Output Voltage 5v and 3.3v Indicator LEDs USB Connector
- Automatic detection of data transfer speeds up to 1Mbps
- Data exchange capability with an external interface with UART protocol
- Supports Windows 8, Windows 7, Windows Vista, Windows XP, Linux, Mac OS X, Windows CE 4.2-5.2, Windows CE 6.0
USB to RS485 Converter Adapter Support WIN7 XP Vista Linux Mac OS
- Fully compliant USB 2.0 standard, backward compatible with USB1.1
- Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive
- Baud Rate Range: 75bps – 115200bps, up to 6Mbps
- Supports Plug, Play and hot-swap ( USB side)
- Better than using CH341D chip or similar chip to support the laptop USB port.
- Communication distance up to 1.2KM
USB to RS485 TTL Serial Converter Adapter FT232
- Baud rate: 300 – 9216000bps, automatically detecting the serial signal data rate
- Load capacity: support multipoint, each converter allows RS485 interface device to connect 32
- Interface Protection: TVS tube protection, USB self-recovery protection
- Support Windows98/ME/2000/XP/WIN7/Vista, Linux, Mac
- It can be up to 32 devices on the bus.
USB TO UART TTL 5V 3.3V FT232RL Download Cable To Serial Adapter Module For Arduino
- Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini
- Original FTDI FT232 chip, stable performance
- USB power has current protection, using 500MA self-restore fuse
- RXD/TXD transceiver communication indicator
- With power, sending, receiving indicator, working status LED indicators
- Mini USB Port Connection
- Support 3.3V, 5V
USB to UART/ESP8266 Adapter Programmer for ESP-01 WiFi Modules with CH340G Chip
- Driver Chip: CH340G
- Supports all basic windows versions.
- The adapter plate integrated 1000μF solid capacitors to ensure the current supply
- The power supply will not be a problem to make WIFI module crashes unresponsive.
- Using 3225 SMD crystal oscillator, improve the stability of serial work, on a beautiful and tall.
- Working voltage: 4.5V – 5.5V (Onboard 3.3v LDO Regulator)
- Working current: 300mA (LDO regulator can supply)