Deals of The Day
Go to Daily Deals SectionAurdino Boards
UNO Based ESP8266 Nodemcu Development Board
Based on ESP-8266EX.
Arduino compatible, using Arduino IDE to program.
Support OTA wireless upload.
Onboard 5V 1A Switching Power Supply (highest input voltage 24V).
The direct use of Arduino IDE development, the same operation with Arduino UNO.
Operating Voltage: 3.3V
Digital I/O Pins: 11
Analog Input Pins: 1
SKU: 100105
Raspberry Pi Display
Raspberry Pi 4 Model B Touchscreen 7 inch Display Case -ABS, Red
Compatible with Raspberry Pi 4 & 7-inch Touchscreen Display
Full access to all ports and controls
Holding slot for Pi Camera
Ventilated design for passive cooling
Enclosure Material: ABS
Body Colour: Orange-Red
SKU: 101106
Drone Transmitter and Receiver
FS-TH9X 2.4GHz 9CH Upgrade Transmitter with FS-IA10B Receiver
Transmitter: FS-TH9X Upgrade with FS-RM003 2.4GHz Module
Receiver: FS-IA10B
Default Mode: Mode-2
Input Power: 12V DC (1.5V x 8 AAA Battery)
Bidirectional System
Frequencies-Hopping
Omni-directional High Gain Antenna
Low Power Consupmtion
SKU: 201021
Laptops & Computers
Go to Daily Deals SectionHeadphones
Go to Daily Deals SectionStepper Motor Driver
TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor
Driver Chip: TB6560AHQ
Operating Voltage: 10-35V
Nominal Voltage: 24V
With the large heat sink to ensure good heat dissipation
6N137 high-speed OptoCoupler, to ensure a high speed without step out.
SKU: 800607
Aurdino Boards
Due AT91SAM3X8E ARM Cortex-M3 Board with Micro USB Cable Compatible with Arduino
Microcontroller: AT91SAM3X8E
Operating Voltage: 3.3V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 6-16V
Digital I/O Pins: 54 (of which 12 provide PWM output)
Analog Input Pins: 12
Analog Outputs Pins: 2 (DAC)
A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock.
CPU clock at 84Mhz
96KBytes of SRAM
SKU: 100101
Aurdino Boards
Pro Mini ATMEGA328P 5V/16M (Official Version)
Microcontroller: ATmega328
Circuit Operating Voltage: 5V
Clock frequency: 16MHz.
Digital I/O Pins: 14
8 analog input port: A0 ~ A7.
A pair of TTL level serial port transceiver : RX / TX.
6 PWM port: D3, D5, D6, D9, D10, D11.
Support serial download.
SKU: 100104
Aurdino Boards
UNO Based ESP8266 Nodemcu Development Board
Based on ESP-8266EX.
Arduino compatible, using Arduino IDE to program.
Support OTA wireless upload.
Onboard 5V 1A Switching Power Supply (highest input voltage 24V).
The direct use of Arduino IDE development, the same operation with Arduino UNO.
Operating Voltage: 3.3V
Digital I/O Pins: 11
Analog Input Pins: 1
SKU: 100105
Aurdino Boards
Due AT91SAM3X8E ARM Cortex-M3 Board, 84MHz, 512KB Board Compatible with Arduino
Microcontroller: AT91SAM3X8E
Operating Voltage: 3.3V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 6-16V
Digital I/O Pins: 54 (of which 12 provide PWM output)
Analog Input Pins: 12
Analog Outputs Pins: 2 (DAC)
A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock.
CPU clock at 84Mhz
96KBytes of SRAM
SKU: 100106
Aurdino Boards
Pro Micro 5V 16M Mini Leonardo Microcontroller Development Board For Arduino
ATMEGA32U4 running in 5V / 16MHz
Support Arduino IDE V1.0.1
Micro USB interface programming on the board
Four 10-bit ADC pin
12 digital I / O (5 PWM capability)
Rx and Tx hardware serial connection
SKU: 100108
Aurdino Boards
Nano Board R3 with CH340 chip without USB Cable compatible with Arduino (Unsoldered)
Operating Voltage (logic level): 5V
8 analog inputs ports: A0 ~ A7
14 Digital input / output ports: TX, RX, D2 ~ D13
1 pair of TTL level serial transceiver ports RX / TX
Using Atmel Atmega328P-AU MCU
Standard 0.1″ spacing DIP (breadboard friendly).
SKU: 100109
Aurdino Boards
Nano Board R3 CH340 chip With USB Mini Cable compatible with Arduino (soldered)
Operating Voltage (logic level): 5V
With USB cable and Soldered Connector
8 analog inputs ports: A0 ~ A7
14 Digital input / output ports: TX, RX, D2 ~ D13
1 pair of TTL level serial transceiver ports RX / TX
Using Atmel Atmega328P-AU MCU
There is a bootloader installed in it
Standard 0.1” spacing DIP (breadboard friendly).
Manual reset switch.
SKU: 100110
Aurdino Boards
Uno R3 CH340G ATmega328p Development Board Compatible with Arduino
Microcontroller ATmega328 (SMD) – Interface CH340G
Operating Voltage: 5V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 5-20V
Digital I / O Pins 14 (of which 6 provide PWM output)
Analog Input Pins: 6
SKU: 100111
TV Entertainment
Go to Daily Deals SectionMicrocontroller IC
ATmega8A U PDIP-28 Microcontroller
Advanced RISC Architecture.
Up to 16 MIPS Throughput at 16 MHz.
On-chip 2-cycle Multiplier.
Write/Erase Cycles: 10,000 Flash/100,000 EEPROM.
Programming Lock for Software Security.
Programmable Serial USART.
Applications of ATmega8 Microcontroller:
Useful for Multiple DIY projects.
SKU: 300703
Hot Glue Gun & Sticks
Standard 60 Watt Corded Glue Gun with 5 Glue Sticks
Comes with an On/Off Switch
Feed Type Trigger-fed Gun
Rated Power: 60 W
Heating Up Time: 5 min
Cord Length: 1 Mtr.
Aluminum Tip
Replaceable Cartridge(Glue Sticks)
Specific Uses of the Product Wood, Plastics, Textiles, Cardboard, Ceramics, Leather, etc
SKU: 400101
Ultrasonic Sensor
Waterproof Ultrasonic Obstacle Sensor, Reversing Radar Sensor with Separate Probe
Integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions
Small size, easy to use
Operating Voltage: 5 V
Sonar Sensing Range: 25-450 cm
Max. Sensing Range: 450 cm
Frequency: 40 KHz
SKU: 600210
Environmental Sensor
Three-Way Soil Meter For Moisture, Light Intensity and pH Testing Meter
Three different soil test meters in one device; Measures moisture, pH/Acidity, and light.
100% Accuracy; Easy to read moisture, pH and light levels; Perfect monitor for growing healthy plants.
Takes the guesswork out of gardening; Know exactly when to water, amend your soil or adjust lighting.
Compact, portable & easy to use, just plug and use; Compact soil meter works indoor/outdoors.
Save water, energy and keep your plants, lawn, flower in top condition.
Measures moisture at root level.
No battery required, simple and convenient to use.
SKU: 600803
Interface Module
MAX485 TTL To RS485
On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver.
A low power consumption for the RS-485 communication
Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring.
Slew-rate limited transceiver
All pins of the chip have been lead to can be controlled through the microcontroller.
Convenient RS-485 communication wiring
Multiple Units can be connected to the same RS-485 bus wiring.
All Chip pins are brought out for proper controls
SKU: 601816
Wi-Fi Module
Ai Thinker LoRa Series Ra-02 Spread Spectrum Wireless Module
Manufacturer: Ai-Thinker
LoRa Spread Spectrum modulation technology
Constant RF power output at + 20dBm-100mW voltage change
High sensitivity: down to -148dBm
Half-duplex SPI communication
Programmable bit rates up to 300kbps
Supports FSK, GFSK, MSK, GMSK, LoRa and OOK modulation modes
SKU: 602113
Stepper Motor Driver
3D Printer Controller Board RAMPS 1.4 Arduino Mega Shield RepRap Prusa Model
Supply Voltage: 12V
Standard interfaces (as that of the extruder)
Reserved GCI like I2C and RS232
3 MOSFET’s are applied to the heater/ fan and thermistor circuit.
Another 5A added to protect the component parts.
An 11A fuse is added to the hotbed.
Support 5 stepper drive board
SKU: 800605
Battery Protection Board
5S 15A 18650 Li-ion Lithium Battery BMS Charger Protection Board for 18V 21V Battery
Battery Protection Board
5S 15A 18650 Li-ion Lithium Battery BMS Charger Protection Board for 18V 21V Battery
Charging voltage: 21V
Charging current: 56 A
Continuous discharge current: 15 A
Over current protection: 50/55/60 A
Over current protection delay: 20/25/30 mS
Single section power consumption since: 30uA
Single section discharge detection voltage: 2.75-2.85V
Over discharge recovery voltage: 2.90-3.20V
SKU: 900503
Smartphones & Tablets
Go to Daily Deals SectionStepper Motor Driver
TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor
Driver Chip: TB6560AHQ
Operating Voltage: 10-35V
Nominal Voltage: 24V
With the large heat sink to ensure good heat dissipation
6N137 high-speed OptoCoupler, to ensure a high speed without step out.
SKU: 800607
Aurdino Boards
Due AT91SAM3X8E ARM Cortex-M3 Board with Micro USB Cable Compatible with Arduino
Microcontroller: AT91SAM3X8E
Operating Voltage: 3.3V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 6-16V
Digital I/O Pins: 54 (of which 12 provide PWM output)
Analog Input Pins: 12
Analog Outputs Pins: 2 (DAC)
A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock.
CPU clock at 84Mhz
96KBytes of SRAM
SKU: 100101
Aurdino Boards
Pro Mini ATMEGA328P 5V/16M (Official Version)
Microcontroller: ATmega328
Circuit Operating Voltage: 5V
Clock frequency: 16MHz.
Digital I/O Pins: 14
8 analog input port: A0 ~ A7.
A pair of TTL level serial port transceiver : RX / TX.
6 PWM port: D3, D5, D6, D9, D10, D11.
Support serial download.
SKU: 100104
Aurdino Boards
UNO Based ESP8266 Nodemcu Development Board
Based on ESP-8266EX.
Arduino compatible, using Arduino IDE to program.
Support OTA wireless upload.
Onboard 5V 1A Switching Power Supply (highest input voltage 24V).
The direct use of Arduino IDE development, the same operation with Arduino UNO.
Operating Voltage: 3.3V
Digital I/O Pins: 11
Analog Input Pins: 1
SKU: 100105
Aurdino Boards
Due AT91SAM3X8E ARM Cortex-M3 Board, 84MHz, 512KB Board Compatible with Arduino
Microcontroller: AT91SAM3X8E
Operating Voltage: 3.3V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 6-16V
Digital I/O Pins: 54 (of which 12 provide PWM output)
Analog Input Pins: 12
Analog Outputs Pins: 2 (DAC)
A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock.
CPU clock at 84Mhz
96KBytes of SRAM
SKU: 100106
Aurdino Boards
Pro Micro 5V 16M Mini Leonardo Microcontroller Development Board For Arduino
ATMEGA32U4 running in 5V / 16MHz
Support Arduino IDE V1.0.1
Micro USB interface programming on the board
Four 10-bit ADC pin
12 digital I / O (5 PWM capability)
Rx and Tx hardware serial connection
SKU: 100108
Aurdino Boards
Nano Board R3 with CH340 chip without USB Cable compatible with Arduino (Unsoldered)
Operating Voltage (logic level): 5V
8 analog inputs ports: A0 ~ A7
14 Digital input / output ports: TX, RX, D2 ~ D13
1 pair of TTL level serial transceiver ports RX / TX
Using Atmel Atmega328P-AU MCU
Standard 0.1″ spacing DIP (breadboard friendly).
SKU: 100109
Aurdino Boards
Nano Board R3 CH340 chip With USB Mini Cable compatible with Arduino (soldered)
Operating Voltage (logic level): 5V
With USB cable and Soldered Connector
8 analog inputs ports: A0 ~ A7
14 Digital input / output ports: TX, RX, D2 ~ D13
1 pair of TTL level serial transceiver ports RX / TX
Using Atmel Atmega328P-AU MCU
There is a bootloader installed in it
Standard 0.1” spacing DIP (breadboard friendly).
Manual reset switch.
SKU: 100110
Aurdino Boards
Uno R3 CH340G ATmega328p Development Board Compatible with Arduino
Microcontroller ATmega328 (SMD) – Interface CH340G
Operating Voltage: 5V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 5-20V
Digital I / O Pins 14 (of which 6 provide PWM output)
Analog Input Pins: 6
SKU: 100111
Cameras
Go to Daily Deals SectionStepper Motor Driver
TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor
Driver Chip: TB6560AHQ
Operating Voltage: 10-35V
Nominal Voltage: 24V
With the large heat sink to ensure good heat dissipation
6N137 high-speed OptoCoupler, to ensure a high speed without step out.
SKU: 800607
Aurdino Boards
Due AT91SAM3X8E ARM Cortex-M3 Board with Micro USB Cable Compatible with Arduino
Microcontroller: AT91SAM3X8E
Operating Voltage: 3.3V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 6-16V
Digital I/O Pins: 54 (of which 12 provide PWM output)
Analog Input Pins: 12
Analog Outputs Pins: 2 (DAC)
A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock.
CPU clock at 84Mhz
96KBytes of SRAM
SKU: 100101
Aurdino Boards
Pro Mini ATMEGA328P 5V/16M (Official Version)
Microcontroller: ATmega328
Circuit Operating Voltage: 5V
Clock frequency: 16MHz.
Digital I/O Pins: 14
8 analog input port: A0 ~ A7.
A pair of TTL level serial port transceiver : RX / TX.
6 PWM port: D3, D5, D6, D9, D10, D11.
Support serial download.
SKU: 100104
Aurdino Boards
UNO Based ESP8266 Nodemcu Development Board
Based on ESP-8266EX.
Arduino compatible, using Arduino IDE to program.
Support OTA wireless upload.
Onboard 5V 1A Switching Power Supply (highest input voltage 24V).
The direct use of Arduino IDE development, the same operation with Arduino UNO.
Operating Voltage: 3.3V
Digital I/O Pins: 11
Analog Input Pins: 1
SKU: 100105
Aurdino Boards
Due AT91SAM3X8E ARM Cortex-M3 Board, 84MHz, 512KB Board Compatible with Arduino
Microcontroller: AT91SAM3X8E
Operating Voltage: 3.3V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 6-16V
Digital I/O Pins: 54 (of which 12 provide PWM output)
Analog Input Pins: 12
Analog Outputs Pins: 2 (DAC)
A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock.
CPU clock at 84Mhz
96KBytes of SRAM
SKU: 100106
Aurdino Boards
Pro Micro 5V 16M Mini Leonardo Microcontroller Development Board For Arduino
ATMEGA32U4 running in 5V / 16MHz
Support Arduino IDE V1.0.1
Micro USB interface programming on the board
Four 10-bit ADC pin
12 digital I / O (5 PWM capability)
Rx and Tx hardware serial connection
SKU: 100108
Aurdino Boards
Nano Board R3 with CH340 chip without USB Cable compatible with Arduino (Unsoldered)
Operating Voltage (logic level): 5V
8 analog inputs ports: A0 ~ A7
14 Digital input / output ports: TX, RX, D2 ~ D13
1 pair of TTL level serial transceiver ports RX / TX
Using Atmel Atmega328P-AU MCU
Standard 0.1″ spacing DIP (breadboard friendly).
SKU: 100109
Aurdino Boards
Nano Board R3 CH340 chip With USB Mini Cable compatible with Arduino (soldered)
Operating Voltage (logic level): 5V
With USB cable and Soldered Connector
8 analog inputs ports: A0 ~ A7
14 Digital input / output ports: TX, RX, D2 ~ D13
1 pair of TTL level serial transceiver ports RX / TX
Using Atmel Atmega328P-AU MCU
There is a bootloader installed in it
Standard 0.1” spacing DIP (breadboard friendly).
Manual reset switch.
SKU: 100110
Aurdino Boards
Uno R3 CH340G ATmega328p Development Board Compatible with Arduino
Microcontroller ATmega328 (SMD) – Interface CH340G
Operating Voltage: 5V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 5-20V
Digital I / O Pins 14 (of which 6 provide PWM output)
Analog Input Pins: 6
SKU: 100111